10A Solar Lighting Timer Controller Mode 10I LED indicator Voltage Settable

10A Solar Lighting Timer Controller Mode 10I LED indicator Voltage Settable

CODE: JW-10I

List price: $8.50  

$6.50

You save: $2.00 (24%)
-24%
In stock

Four load working modes:

Pure lighting control

lighting control &timing control,

hand operation 

debug mode.

 

Features:

12/24V automatic recognition 

·High efficient Series PWM charging, increase the battery lifetime and improve the solar system performance. 

·Use MOSFET as electronic switch, without any mechanical switch 

·Widely used, automatically recognize day/night. 

·Digital LED menu, only one key solve all setting simply 

·Intelligent timer function with 1-15 hours option 

·Unique dual timer function, enhance the flexibility of street light system. 

·Gel, Sealed and Flooded battery type option. 

·Adopt temperature compensation, correct the charging and discharging parameters automatically 
and improve the battery lifetime. 

·Electronic protection: Overheating, over charging, over discharging, 

overload, and short circuit. 

·Reverse protection: any combination of solar module and battery. 

Settings

. Load Control Settings 

1. Dusk to Dawn 

When solar module voltage goes below the point of NTTV (Night Time Threshold Voltage) at sunset, 
the controller will recognize the starting voltage and turn on the load after 10 minutes delay. When 
solar module voltage goes above point of DTTV (Day Time Threshold Voltage), the solar controller 
will recognize the starting voltage and turn off the load after 10 minutes delay. 

2. Light ON + Timer 

When solar module voltage goes below the point of NTTV (Night Time Threshold Voltage) at sunset; 
the solar controller will recognize the starting voltage and turn on the load after 10 minutes delay. The 
load will be on for several hours which users set through LED digital tube. The controller has dual timer
function. Please refer to table 4-5-Load Work Mode Setting II. 

3. Test mode 

This mode is the same as Dusk to Dawn. But there is no 10 minutes delay when controller recognizes 
the starting voltage. When below the starting voltage, the controller will turn on the load, if higher, it will
turn off load. 

The test mode makes it easy to check the system installation. 

4. ON/OFF mode 

This mode is to turn ON and OFF the load by manual. 

A.Load Work Mode Setting 

When the led digital tube is not display, Press the setting button "Key" more than 5 seconds , 
and keep on press it once more,led digital tube will  be changed once among

 

    0  Load work mode
    b1    Battery type
   J0   Load start-up delay
   S5   Optical sensitivity
   F0   Float charging voltage
   H0   Low voltage reconnect voltage
   q0

  Low voltage disconnect voltage

   8.8.  Restore factory Settings.

 

Describe

LED digital No.

Dusk to Dawn, Load will be on all night

0

Load will be on for 1 hour after ten minutes delay since sunset

1

Load will be on for 2 hour after ten minutes delay since sunset

2

Load will be on for 3 hour after ten minutes delay since sunset

3

Load will be on for 4 hour after ten minutes delay since sunset

4

Load will be on for 5 hour after ten minutes delay since sunset

5

Load will be on for 6 hour after ten minutes delay since sunset

6

Load will be on for 7 hour after ten minutes delay since sunset

7

Load will be on for 8 hour after ten minutes delay since sunset

8

Load will be on for 9 hour after ten minutes delay since sunset

9

Load will be on for 10 hour after ten minutes delay since sunset

10

Load will be on for 11 hour after ten minutes delay since sunset

11

Load will be on for 12 hour after ten minutes delay since sunset

12

Load will be on for 13 hour after ten minutes delay since sunset

13

Load will be on for 14 hour after ten minutes delay since sunset

14

Load will be on for 15 hour after ten minutes delay since sunset

15

ON/OFF mode

16

TEXT mode

17


Data Sheet:

 

Description

Parameter

Nominal System Voltage

12 / 24VDC Auto work

Battery Voltage Range

6-36V

Rated Battery Current

10A,20A,30A

Charge Circuit Voltage Drop

≤0.26V

Discharge Circuit Voltage Drop

≤0.15V

Self-consumption

≤6mA

 

Threshold Voltage Parameters

Description

Parameter

NTTV (Night Time Threshold Voltage)

5V; x2/24V

DTTV (Day Time Threshold Voltage)

6V; x2/24V

 

Temperature Compensation Coefficient

 

Description

Parameter

Temperature Compensation (TEMPCO)*

-25mV/°C/12V[25°C ref]

 
* Compensation of equalize, boost, float and boost reconnect voltage
 
Battery Voltage Parameters (temperature at 25°C

Charging setting

Sealed

Flooded

Gel

Over voltage disconnect

15.5V;x2/24V

Charging limit voltage

15.0V;x2/24V

Equalize charging voltage

14.6V;×2/24V

14.8V;×2/24V

14.4V;×2/24V

Boost charging voltage

14.4V;×2/24V

14.6V;×2/24V

14.2V;×2/24V

Float charging voltage

13.8V;x2/24V
Boost reconnect charging voltage
13.2V;x2/24V
Low Voltage reconnect voltage
12.6V;x2/24V
Under Voltage warning reconnect voltage
12.2V;x2/24V
Unver voltage warning voltage
12V;x2/24V
Low voltage disconnect voltage
11.1V;x2/24V
Discharge limit voltage
10.8V;x2/24V
Equalize duration
60min

Boost duration

60min

Environmental parameters

Parameter

Working temperature

-35°Cto +55°C

Storage temperature

-35°C to +55°C

Humidity

10%-90% NC

Enclosure

IP30

Type the characters you see in the picture above.

Loading...